Spray paint a motorcycle by powder coating the frame
The best way to spray paint a motorcycles frame
With thousands of Internet searches a month ending at Windridge Coatings, we have become one of the best-known powder coaters for repainting the best motorbike frames. With meticulous attention to detail we are able to achieve the quality finish previously only available with liquid paint. Blasting and powder coating is not the whole story this page will explain why.
Who should use Windridge Coatings?
Owners who do not want a quick cheap job, but those who need to be reassured their precious bike is going to be looked after and worked on with care and interest. Every body admires a bike with a good paint finish. We are used when nothing less than the best quality is good enough. For perfectionists who rebuild their bikes to Concours d’Elegance standard.
The Tri-Resin™ System
An advantage of using an architectural powder is the depth of knowledge and facilities for protecting steel for at least fifteen years in all weathers. Coupled with a background of spraying quality cars, achieving a good finish for Windridge Coatings is second nature. The Tri-Resin System incorporates the best practices of corrosion inhibitors, liquid painting and powder coating. It is the way of the future for powder coating and your motorbike frame will look good and be better protected for it.
Powder coating looks good is tough and corrosion resistant
Not all bikes are gently ridden and spend most of their time being polished. Our powder coating is for hard working bikes that need good corrosion protection and resistance to chipping.
Click here for information about coating quad bikes and ATVs... more
But powder coating is not the original paint
Neither is two pack polyurethane. All paints are made of pigment, resins and extenders. With wet painting solvents are used to dissolve these into a liquid paint easy for application but with powder coating there are no solvents; the heat is used to turn its ingredients into a liquid. When both are cured the average person would not be able to tell the difference between the two finishes. See below
How to present your frame for powder coating
Please present your frame with all brackets, fittings, bearings, grease and road dirt removed. Some modern bike frames are powder coated which is difficult to remove without damaging your frame with excessive blasting. To thoroughly clean your frame of existing paint and contaminants a controlled pyrolysis oven is used prior to blasting this will also remove any rubber or plastic left fitted.
Special colours not available in powder
If the bike requires a special colour unavailable in powder, many clients ask for the frame to be striped, blasted and primed in powder. It can then be wet painted in two-pack polyurethane, acrylic, cellulose, or many other types of wet paint. This has the advantages of the protective qualities of powder with the colours of wet paint.
What we do to your frame
The following will show the different stages of processing your frame will go through at Windridge Coatings. Gently removing paint and grease with controlled heat prior to blasting.
Removing paint and grease
The old paint and all grease needs to be removed from the frame or it will spoil the new powder coating. Blasting alone cannot do this and any grease left, will run over the new paintwork when the frame is heated. The controlled pyrolisis process we offer is not used by many of our competitors. It is a special oven that carefully heats the frame to about 400 degrees Celsius to turn the paint, grease and any other contaminants into ash. Heating the component slowly and evenly avoids distortion.
Pyrolisis semi anneals the frame to relieve internal stresses and reduces cracks
Heat treatment has another useful advantage with semi annealing the frame to reduce internal stresses accumulated by years of hard riding. The metal becomes work hardened, which leads to metal fatigue and is the cause of frame cracks. See below.
To remove the ash Windridge Coatings grit blast motorbike frames. Grit blasting sometimes referred to as sand blasting or shot blasting removes the surface of the metal including rust. To reduce the amount of blasting so as not to weaken the frame we always remove paint first either by incineration or paint striping. Especially on modern frames that are often powder coated and is difficult to remove by blasting alone.
To reduce the likely hood of the frame rusting under the paintwork a corrosion inhibitor is applied. This is an architectural metal pre-treatment process used to seal the metal after blasting. A concoction of chemicals passivate the metal combined with a low viscosity paint ensures no metal is left uncoated. Around brackets and the air pockets under the powder coat which can be the starting areas for under coat rust creep. This is an expensive process that would not normally be used on motorbike frames.
Fatigue crack inspection
Grit blasted frames are checked for fatigue cracks prior to painting. The above image shows part of a TT sidecar that was condemned because we found a number of cracks through out the frame, all of which would not have been seen with out our inspection.
Powder coat primer
Priming a motorcycle frame is very important, as it is the waterproof barrier. Polyester powder coat on its own is not sufficient protection on steel against corrosion. The primer is expensive and most powder coaters will leave out this stage because the customer cannot see it. Not only will it prolong the life of the frame against rust but it also produces a smoother finish. A knowledgeable powder coater must apply the primer or the paint will be prone to cracking. To avoid the frame number being lost Windridge Coatings masks the serial number at primer stage. Depending on how prominent the number is we may not powder coat over it all but lightly wet paint.
Perfect paint finish
We use one of the most expensive black powders on the market to give you the deepest glossiest black. Treat it like any other paint, wash, compound and wax and it will last for decades.
Powder coat testing
Windridge Coatings often gives talks to bike clubs and exhibits at bike shows. To prove powder coating is tough and not brittle when applied correctly, sample panels are tested by impact with a 2lb ball pein hammer. The testing is carried out in front of an audience who are always impressed with our confidence.
Tests adhesion, curing, quality of paint
This simple field test is based on a BS3900-E7. If the domed paint exhibits cracks, it can indicate poor key, dirty metal i.e. grease under the paint, inadequate curing or poor quality powder, which can be brittle. This means the paint is likely to chip during use, paint will crack under pressure from bolts and paint cracking with flexing of the frame, all of which will allow moisture to start rusting.
How much does it cost to powder coat a motor bike frame
The price to powder coat a standard frame in black is £145 +VAT. To help you estimate prices for your components here are a few examples:
- Main stand: £15 +VAT
- Side stand: £12 +VAT
- Head light shroud: £20 +VAT
- Mudguard: £35 +VAT
- Steel swing arm: £35 +VAT
Please allow an extra £25 for colours. Approximately 100 colours to choose from.
For a comparison between stove enamel and powder coating click here... more